Three-one motor

Stainless Drill Chuck

Keyed Grip for Shafts That Slip.

A stainless steel drill chuck that replaces the hand-tightened chuck on Three-One Motor mixers, for shafts that need a chuck handle to clamp securely. Holds shafts of ø8 mm and below.

Replaces the hand-tightened chuck: fits in its place on the motor's drive shaft
Keyed clamping: the chuck handle tightens harder than hand pressure for heavy or long shafts
ø8 mm and below: the same shaft range as the hand chuck

Fits with: BL, BLh, BL Saf, BLh Saf, BL Ft, BLh Ft, TE, and BL600Z mixers (hand-tightening chuck models).

$110.00

TE1200 Torque Measurement Laboratory Mixer

The Torque Meter That Also Mixes. Every overhead stirrer with a torque display is estimating from motor current. This one measures. A calibrated strain-gauge transducer sits in the drive path between motor and shaft, reads the actual torque on the blade to three decimals, and sends it out as a 0 to 5 V signal you can log, chart, and hand to another department. The drive is an 80 W Three-One Motor: 0.5 N·m, 20 to 1200 rpm held by feedback control, built for syrups, solutions, and the thin batches that build as they run.

Mixers killed by overload: The current limiter keeps the motor driving through loads that shut ordinary mixers down. No throw-away mixers, no burned-out windings, no throw-away batches.
Torque figures nobody outside the lab will accept: A factory-calibrated through-shaft transducer, not a motor-current estimate, gives a number that survives scale-up meetings and external review.
Unmixed layers single-direction mixing leaves behind: Set forward and reverse cycles once and the mixer alternates automatically for the entire run, breaking up the ring-shaped dead zones.

SKU TE1200 Category Laboratory Mixers and Mixing Systems Tags Heidon mixer, laboratory mixer, overhead stirrer with torque sensor, strain gauge torque meter, TE1200, TE1200P, TE1200S, Three-one motor, torque measurement mixer, torque transducer mixer

Price range: $16,395.00 through $16,995.00

CC Keyless Chuck Collets

Run Any Shaft Diameter in the Hand-Tightening Chuck

Interchangeable collets that adapt the keyless chuck to shaft diameters from ø2 to ø8 mm. Swap the collet, and thin shafts and Teflon-coated cores grip as securely as the standard ø8.

Five diameters: ø2, ø4, ø5, ø6, and ø8 mm collets cover every shaft in the system
Teflon blade ready: The ø5 collet matches the steel cores common on Teflon-coated blades
Tool-free swaps: Collets change in the hand-tightening chuck without a chuck key

Fits with: BL, BLh, BL Saf, BLh Saf, BL Ft, BLh Ft, TE, and BL600Z mixers (hand-tightening chuck models).

SKU CC Category Accessories - Laboratory Mixers and Mixing Systems Tags CC-2, CC-4, CC-5, CC-6, CC-8, CC2, CC4, CC5, CC6, CC8, chuck collet, Heidon accessories, keyless chuck collet, mixer collet, Three-one motor

$98.00

EP200 Air Motor Laboratory Mixer

No Electricity. No Ignition Source. 2.6 N·m. Some rooms allow no electrical equipment at all, and some mixing points are simply nowhere near an outlet. This mixer needs neither. An air motor rated 0.3 HP turns the shaft, a needle valve on the panel sets the speed, and a regulator and lubricator in the included separator unit condition the supply. Rated 190 rpm with 2.6 N·m allowable torque, for pastes, adhesives, and solvent-based creams. Nothing electrical enters the room.

Rooms where nothing electric is allowed: The drive is an air motor and the controls are a needle valve. There is no motor winding, no display, no cable, and nothing to certify. Connect 0.5 MPaG air and mix.
Air mixers that arrive as a kit of parts: The separator unit with filter, lubricator, regulator, and turbine oil ships in the box with the hose, chuck handle, and clamp holder.
Overload that breaks the gears: Allowable torque is a hard limit on an air motor, so match the model to the material: lower rated speed, higher torque.

SKU EP200 Category Laboratory Mixers and Mixing Systems Tags air driven mixer, air motor laboratory mixer, EP200, EP200P, EP200S, hazardous area mixer, Heidon mixer, pneumatic overhead stirrer, solvent mixer, Three-one motor

Price range: $4,795.00 through $5,495.00

EP400 Air Motor Laboratory Mixer

Air-Driven Torque for Coatings and Gels. Some rooms allow no electrical equipment at all, and some mixing points are simply nowhere near an outlet. This mixer needs neither. An air motor rated 0.3 HP turns the shaft, a needle valve on the panel sets the speed, and a regulator and lubricator in the included separator unit condition the supply. Rated 400 rpm with 1.3 N·m allowable torque, for coatings, gels, and solvent-thinned creams. Nothing electrical enters the room.

Rooms where nothing electric is allowed: The drive is an air motor and the controls are a needle valve. There is no motor winding, no display, no cable, and nothing to certify. Connect 0.5 MPaG air and mix.
Air mixers that arrive as a kit of parts: The separator unit with filter, lubricator, regulator, and turbine oil ships in the box with the hose, chuck handle, and clamp holder.
Overload that breaks the gears: Allowable torque is a hard limit on an air motor, so match the model to the material: lower rated speed, higher torque.

SKU EP400 Category Laboratory Mixers and Mixing Systems Tags air driven mixer, air motor laboratory mixer, EP400, EP400P, EP400S, hazardous area mixer, Heidon mixer, pneumatic overhead stirrer, solvent mixer, Three-one motor

Price range: $4,795.00 through $5,495.00

EP700 Air Motor Laboratory Mixer

Air-Driven Dissolving Where Power Cannot Go. Some rooms allow no electrical equipment at all, and some mixing points are simply nowhere near an outlet. This mixer needs neither. An air motor rated 0.3 HP turns the shaft, a needle valve on the panel sets the speed, and a regulator and lubricator in the included separator unit condition the supply. Rated 700 rpm with 0.7 N·m allowable torque, for solvent solutions, inks, and thinned coatings. Nothing electrical enters the room.

Rooms where nothing electric is allowed: The drive is an air motor and the controls are a needle valve. There is no motor winding, no display, no cable, and nothing to certify. Connect 0.5 MPaG air and mix.
Air mixers that arrive as a kit of parts: The separator unit with filter, lubricator, regulator, and turbine oil ships in the box with the hose, chuck handle, and clamp holder.
Overload that breaks the gears: Allowable torque is a hard limit on an air motor, so match the model to the material: lower rated speed, higher torque.

SKU EP700 Category Laboratory Mixers and Mixing Systems Tags air driven mixer, air motor laboratory mixer, EP700, EP700P, EP700S, hazardous area mixer, Heidon mixer, pneumatic overhead stirrer, solvent mixer, Three-one motor

Price range: $4,795.00 through $5,495.00